Friday, May 28, 2010

latest technology

One look at these photos and you know this motorcycle is in the concept stage as I cannot remember seeing any of these on the road.

This is the SunRed solar-powered motorcycle that won the Best Innovative Technology award at the Barcelona Int’l Auto Show, this does look pretty cool and anything that is good to the environment and can be classed as gadget or latest technology is good in my books.

Best Innovative Technology

This SunRed project in the near future will result in a life-size prototype of the solar-powered motorcycle, the prototype will be able to store electrical power from captured sunlight and power the motorcycle in the most environmentally-friendly way.

The clamshell looking motorcycle is built that way to optimize the panel’s surface and to make the vehicle not too bulky. The SunRed solar-powered motorcycle is not moving it can store energy for up to 20km (13 miles) and travel at around 50km/h (30 mph).

Most modern electric bikes are designed in the same way as the motor on this solar-powered motorcycle; it is placed right in the axle of the wheel and brushless.

Now we got to remember this vehicle designed by SunRed is just a concept, but the company hopes that this will become a benchmark for future developments of solar applications in different vehicles.

Solar Power Motorbike

Latest technology Curing light-LT


Introductions:
1. the shiner is more powerful than LED,can solidify any material;
2. fast,solidify depth 3-4mm in 5~10 second;
3. microcomputer controlled 3 work mode:gradually
stronger,flash,smooth;
4. automatic timing at every 10 second;
5. automatic power-off after 3 minute;
6. the shiner is small enough to be settled at the tip,so the tip is
very small(diameter 12mm) and there is no light-leader with bend,so:
7. no need wide-opened mouth;
8. no obstacle to the doctor's line of sight;and
9. cold,almost no heat can be felt;
10. the shiner can work more than 10,000 hours;
11. spend little energy:can work more than 100 times after a well recharging;
12. small and light:length 173mm,the handle diameter 23mm,about 50g
13. voltage 100-240V,50-60Hz;power 1-5W.

parameters:
wavelength:400-490nm,
light intensity:550-580mv/square mm,
power source:110-240V,50-60Hz,
power expended:1-5W

Latest Technology

Having recently invested over half a million pounds within the last 5 years on machinery and infrastructure of the company we have demonstrated our wish to push Adwin Spring forward, thus giving you the benefit of increased capacity and high precision along with better leadtimes.

Investments have been made in all areas, including IT, Quality Control, Machinery, Training and working environment.

Some of the jewels in our crown are shown below.

Starrett Shadowgraph
Sodick K1C

Wafios FSE33
High Speed Coiling Machine

Coupled with our smaller FSE23 we are able to produce large either small batches or large volumes of coil spring very quickly from one of the fastest machines in the world.

Starrett VB400
Optical measuring system.

This enables us to measure
your parts to a high degree of
accuracy ensuring that you
get your parts not only fast,
but also correct.

Sodick K1C
High Speed Small Hole Driller

A perfect compliment to our 2 sodick wire erosion machines, capable of drilling small holes through hardened steel.

Sodick AQ325L Bridgeport VMC600

Sodick AQ325L
Wire Erosion Machine

We Believe we are the 1st spring company in the UK to have 2 wire erosion machines. And with the latest in linear driven technology you get the benefit of increased speed and accuracy.

Bridgeport VMC600
Vertical Machining Centre

Customised to also offer high speed machining as well as conventional machining, and coupled with state of the art CAD & CAM software, we have the total 3D package.

Nucoil FX-20
CNC Wire Forming Machine

This new machine now offers us the ability to produce wireforms, torsion springs and tension springs quickly and accuratly with superb repeatablilty.

NC4

Vixen Jet Air
Shot Peening Machine

This is the latest Vixen Surface Treatments tumble blast machine, using S170 shot it has a slow tumbling barrel which gives the whole spring a complete peened finish vastly prolonging spring life.

Renishaw NC4
Laser Tool Height Measuring System

This system now allows us to accurately check the relaive heights of tools, giving us much increased accuracy, a better suface finish and improved set up times on machined parts and tooling.

Renishaw OMP 40
Machine Touch Probe

This now allows us to accuratly check and set up jobs on our machining centre, giving us increased accuracy and improved set up times on machined parts and tooling.

Lates technologies

It bears more than a passing resemblance to an old-fashioned carriage, but Mercedes-Benz claims this roadster could be the car of the future.

Built by 150 trainees, the car combines traditional design features with the latest technology.

Mercedes-Benz

Mercedes-Benz

So while it has large spoked wheels that hark back to the first Benz Motor Car of 1886, it is powered by a hybrid drive system using an emission-free fuel cell.

It can reach a top speed of 15.5miles an hour and has a range of 220miles.

The students from Daimler AG have worked on the overall concept, development, assembly, and completion of the F-CELL Roadster for a year. The project was created to train the junior employees in alternative drive systems.

 car

The car has a top speed of 15.5miles an hour

joystick
engine

The car is operated by a joystick and powered by an electric motor

They included carbon-fiber bucket seats with hand-stitched leather covers and a distinctively styled fiberglass front section, inspired by Formula One racing cars.

The roadster is controlled with drive-by-wire technology, and a joystick takes the place of a conventional steering wheel.

'I am delighted to see how much initiative and creativity the young people have put into this project,' Labor Relations Manager Günther Fleig said.

Enlarge roadster

The Mercedes-Benz F-CELL Roadster has similar spoked wheels to the first Benz Motor Car

Lates cars

mercedes-benz_f500_mind_concept_2003_014-copy.jpg

The F 500 Mind showcases the very latest technology
At the Tokyo Motor Show 2003, Mercedes-Benz presented the latest in a string of research vehicles which have attracted much interest and attention over the years and which provide fascinating insights into the automotive technology of tomorrow and beyond. Packaged as a modern four-door fastback saloon, the F 500 Mind mobile research lab showcases more than a dozen ideas for enhancing the safety, drive technology and comfort of future Mercedes passenger cars.

The DaimlerChrysler researchers will be using this vehicle to conduct the first practical tests of these innovative systems and pave the way for their commercialisation. The raft of innovations extends all the way from the night vision system with infrared laser headlamps to two-way doors and a programmable multivision display in the cockpit. Electronic accelerator and brake pedals, an interior pillar which provides structural rigidity and an ultrasound driver information system are further features being tested by Mercedes-Benz in the F 500 Mind.

mercedes-benz_f500_mind_concept_2003_002-copy.jpg

For the powertrain, the DaimlerChrysler researchers have developed a high-performance diesel hybrid unit whose NEDC fuel consumption is up to 20 per cent lower than that of a comparable CDI engine. The state-of-the-art V8 diesel engine (184 kW/250 hp) from the S-Class has been combined with a powerful electric motor (50 kW) which is switched on and off by an electronic controller in response to traffic conditions and driving style. The electric motor can take over for example when moving off from rest, in stop-go conditions or in other situations where an internal combustion engine does not operate at optimal efficiency. When the driver demands more power, the V8 internal combustion engine cuts in to provide sharp acceleration. The 300 V battery for the electric motor is located under the passenger cell and is recharged during braking.

mercedes-benz_f500_mind_concept_2003_009-copy.jpg

With a body length of 5092 millimetres and a wheelbase of 2965 mm, the F 500 Mind offers a significant gain in legroom in the rear compared with a conventional present-day saloon in this class. This was made possible by using innovative-design electronic accelerator and brake pedals which take the form of pressure-sensitive surfaces. Sensors in these “pedals” transmit the driver’s commands to the engine and SBCô brake system by means of electrical impulses. The technology takes up much less room than conventional mechanical pedals, increasing the length of the front footwell by 120 millimetres. The driver’s and front passenger’s seats can therefore be positioned further forward, so providing more space for the rear passengers. The steering, too, is controlled electronically.

mercedes-benz_f500_mind_concept_2003_011-copy.jpg
Intelligent door-opening technology allows the doors to be opened in two different ways: either conventionally (both doors open forwards) or from the centre (centre-opening). In the latter mode, the B-pillar stump moves backwards with the rear door to provide a 1900 mm-wide opening for occupant entry and exit.

mercedes-benz_f500_mind_concept_2003_012-copy.jpg

In the absence of full-size B-pillars, which would normally provide the all-important structural rigidity and side impact protection, the Stuttgart engineers came up with an innovative interior pillar which provides exemplary rigidity and typical Mercedes standards of occupant safety. The pillar is located in the middle of the vehicle towards the rear, and connects the reinforced floor pan to the roof structure. It also houses the air-conditioning ducts and interior lighting units.

The multivision display in the cockpit of the F 500 Mind forms the centrepiece of an innovative instrumentation and control system which offers the driver more flexible information delivery and at the same time reduces fatigue. The dials and displays in the instrument cluster are programmable and their images can be optically superposed or combined with the aid of a semitransparent mirror. In this way the driver can call up a wide range of information at the push of a button on the steering wheel. The information is always displayed directly in the driver’s field of vision where it can be seen easily and will not distract him. A further display, the central display unit, is situated above the centre console. It is linked to a touchpad whose surface is divided up in exactly the same way as the surface of the central display. By briefly touching it, the driver can control the navigation system, radio, air conditioning, telephone and other systems.

mercedes-f500-copy.jpg

Further switches and keys in the vehicle are equipped with special sensors which can detect the driver’s approaching hand even at a distance of several centimetres. They then immediately call up the relevant function in the central display, for more convenient operation.

An advanced-design voice control system and an ultrasound-based driver information system take convenience even further. The ultrasound technology targets the sound at the driver so that only he or she can hear the information from the navigation system, the traffic news and other sound-based information sources, while the front passenger and rear passengers remain undisturbed.

In the dark or in poor visibility, the innovative night vision system projects its images onto the right-hand display. The night vision system consists of two infrared laser headlights on the front of the vehicle which “illuminate” the road with their invisible light over a range of up to 150 metres. The light reflected back from other vehicles, cyclists or pedestrians to a camera mounted on the front windscreen of the F 500 Mind is projected in black and white onto the multivision display. This allows the driver to spot hazards much earlier than in a vehicle operating on conventional dipped headlamps, which have a range of only about 40 metres. Thus Night Vision offers further opportunities for making night driving safer.

As a mobile research lab, the F 500 Mind is equipped with a special “laboratory bench” which folds out towards the rear. This allows a researcher sitting in the back of the vehicle to monitor and control the vehicle systems during testing on the proving grounds and to carry out measurements. For example the researchers are planning to use this fascinating vehicle for intensive user acceptance-testing of the innovative instrumentation and control system and for further practical testing of the diesel hybrid drive system and the Night Vision system.

lates technologys

Knowledge and use of mechanical arts and science is called technology. It actually is a broad term, which encompasses in it the information dealing with how one uses the available tools and crafts to create something somehow controls and becomes a part of his environment. We somehow relate technology with science, engineering and computers which however is not quite correct because technology can be involved in arts, architecture, agriculture, in economical development and wherever we can see involvement of machinery, hardware and utensils becoming a part of systems and techniques of an organization. If you like upto date technology then you'll love the new nokia n97.

For different time periods different things can be called technology. For stone age prehistoric people invention of fire and wheel was technology, for middle age people the horse and donkey carts were technology and for us the next generation cars, planes, ships and other vehicles were technology. The progress in the scientific technology has been beyond explanation. Being able to sit at home and surf through hundreds of channels at one time just by sitting in front of the television, with the help of a remote only is technology, Switching on lights and music system by a simple click of a remote is technology; burning of a stove just by turning the knob to open is technology. In short wherever we look, we are surrounded with technology. May it be schools, banks, offices, or even the local grocery store. Since our childhood we were always told that the solar system comprises of nine planets revolving around the huge ball of fire, the sun .it is technology in the field of astronomy, which has now led us to know that the ninth planet, Pluto, is not actually a planet. It is technology only, which has led man to reach not only moon but also mars. Using a computer without antivirus software can be dangerous.

The latest and the most in demand technology these days are the mobile phones. They not only help you keep in touch with the user at all times but offer entertainment as well. The mobile phones these days are a complete entertainment package. They not only let you talk, send messages but also listen to mp3 songs, watch the videos, take digital pictures, use the calendar, the calculator and the alarm clock. Cell phones are a must these days. They are a necessity. The latest technological development in the cell phones is the use of GPRS, which allows you to use internet on your cell phones. You can send emails, chat on messengers or just surf for latest ring tones, wallpapers and themes for your cell phones.

There was a time when computer was the latest technology but now information technology, an entirely new field that is completely different exists. The field of Information technology is being developed on a day-to-day basis. It has opened up many job opportunities for the people at large. The field of information technology has brought a great relief to the youngsters of today by preventing them from being jobless instead become bread earners for their family. The beauty of this field is that all you need to do is become IT certified, get to a few computer languages and become a member of the fast advancing world. It helps you become a part of the rat race for success. Keeping updated about technology is no big deal as all you got to do is get online and type the correct word for the search.

With the passage of time advances are being made in the fields of science, engineering and computers in order to keep up with the pace of the developing world we have to keep ourselves updated regarding the latest technology. Being updated with the latest technology helps you get an edge over other people for getting jobs and if already employed you will get better opportunities for sure. For better job status you have to continuously strive hard and keep on updating your technological knowledge SEO, web design, SEO services, website design - Panasonic LumixF2

Subscribe Tech Talks
Give Email ID
Share Tech Talks
Tech Talks
Home
News
Technology
Information Technology
Technology Trends
Technology Blog
I-phone
Laptops
Modern Technology
Virus and AntiVirus
Windows Vista
Windows XP
Internet History (Page: 1 )
Top 100 Sites (Page: 1 2 3 4)
Create Your Site
Blogs
About Us
Contact Us
TechTalks has been acknowledged as one of top software review web site of 2010 and recognized as one of the simplest softwares review site like CNET, Lifehacker, PC World and TechCrunch.